Filtre de recherche
Filtre de recherche
Produits
Fournisseur
Catégories
Fabricant
Produits ()
Catégories ()
Distributeur ()
Fabricant ()
DMF 260|11 (Reference-Nr. 030318)
Demande concernant cette machine
Asking price
- Numéro de référence 030318Année de construction 2023Heures de fonctionnement non renseigné
-
Offreur
Catégorie principale
Machines pour le travail du métalCatégorie
FraiseusesType de machine
Fraiseuses à banc avec support réglableFabricant
DMG MORICommande
SiemensDescription
General in travelling column construction NEW DMG MORI Design swivel head (B-axis) speed range 20 up to 10,000 rpm motor spindle with 52/42 kW (40/100%DC) tool taper HSK-A100 DIN 69893 tool clamping according to DIN 69872; Control: CELOS with Siemens 840D sl Operate Tool changer Type of gripper Double gripper Type of magazine Chain Number of tools 60 Max. tool weight 12 Kg Max. tool length 500 mm Max. tool diameter with occupied adjacent pockets 115 mm Max. tool dia. with free neighbouring pockets 160 mm Technical Data Feed rate longitudinal/transverse/vertical 80000/80000/80000 mm/min Rapid traverse longitudinal/transverse/vertical 80/80/80 m/min Working area 1 Longitudinal 2600 mm Cross 1100 mm Vertical 900 mm Spécification
Direct measuring system Direct path measuring system Cabine Full protection cabin Dynamic package for DMF 260 linear (Y1100) Dynamic package for DMF 260 linear (Y1,100 mm) linear drive X-axis with 80 m/min // 262.48 ft/min rapid move XYZ 80/60/60 m/min // 262.48/196.86 ft/min, Acceleration XYZ 5/6/6 m/s² // 16.4/19.68 ft/s² Active chiller for main spindle and Linear motor mag Rigid table with integrated rotary axis (leftside) Rigid table with integrated round table d 1050 mm // 41.3 in, located in the left working area table load max. 1,200 kg// 2,644 lbs hydraulic clamped in position Table surface 3200 x 1100 (Ø 1050) mm Clamping hydraulics,2 circuits,Rigid-/Round table Clamping hydraulic for rigid/integrated round table, 30-240 Bar, 2 circuits Rotation speed max.4. Axis 50 rpm Distance between T-Slots 100 mm Number of Slots 11 Slot width 18 mm Removable partition wall DMF260 (Y1100) Partition wall removable for pendulum machining DMF260, 2 working spaces (possible with integrated round table) Tool magazine 60 places SK50/HSK-A100 Tool magazine 60 places SK50/HSK-A100 Chain type with double gripper Mechanical setup station Mechanical setup station SK50/HSK-A100 Load support for tool magazine Load support for tool magazine SK50/HSK-A100 with 2 pockets at the stairs to magazine Spindle speed 20 - 10,000 rpm HSK-A100 430 Nm Spindle speed 20 - 10,000 rpm HSK-A100 for tool taper according to DIN69893 with power 52/42 kW // 69.7/56.3 hp with torque 430/300 Nm (40/100% ED) (differently from standard) 3D quickSET elevated constructuion 3D quickSET Tool kit for control and compensation of the cinematic accuracy of 5 axis machine configurations include additional fixture for elevated construction (only with option touch probe) Tool laser measuring Blum Laser tool measuring Blum (not with TT 140 possible, for pendulum machining please order 2 pieces) Oil mist separator Oil and emulsion mist separator system 2 pieces per machine implemented in right and left cabin side wall. mechanical filter system 2x1600 m³/h Signal lamp 4-colour Signal lamp 4-colour Red: general error Yellow: intervention necessary Green: automatic mode Blue: set-up mode Air blast through spindle centre Air blast through spindle centre activated by M function, maintained air, low oil rate possible Internal Coolant Supply 80bar/980l frequency controled Internal coolant supply (ICS) with paper type filter Papertype-Filter 20-80 Bar // 290-1160 psi frequenzy controlled 980 l tank // 258.8 gallon inclusive 2 rotating clear window, air purge for linear measuring system, rotary joint for main spindle Chip flushing for working area Flushing for working area Additional flushing of the working area doors and cabin sidewalls, Bed flushing included Double cartridge filter,25 µm Double cartridge filter, Finesse of filtration 25 µm (only in combination with internal coolant) Coolant tempering for internal coolant 980l Coolant tempering for internal coolant unit 980l / 259 gallon: Heating capacity max.: 4 kW / 5.3 hp Cooling capacity max.: 4 kW / 5.3 hp (only in combination with internal coolant unit 980l) Door drive for working area doors Door drive for working area doors Open / close - activated by two-hand-operation at the control panel Safety sensor technology for prevention of accidents MPC Machine Protection Control MPC Machine Protection Control Machine protection by quick shutdown proTIME proTIME Visualisation of remaining runtime, remaining workpieces and the machine state Application Tuning Cycle ATC Application Tuning Cycle ATC programmable feed parameter selection for machining task: accuracy/surface/speed Operation mode 4 Operation mode 4 Process monitoring in the production Manual intervention with open doors of machining area. Release after check list has been filled in. Turning/Milling cycle Turning / milling cycle For the machining of internal and external diameter using spindle orientation DXF Reader DXF-Raeder: Open CAD files Extracting of counters and drilling positions directly in G-code and ShopMill programs Supported elements: drilling positions and contours angularTOOL angular TOOL Technology cycle for programming of a 360 degree rotatable angular head tool Laminated safety glass Laminated safety glass for Windows in the two front doors Exhibition design DMF Exhibition design DMF chiller of electrical cabinet painted in electrical cabinet color; lighting of tool magazine; DMG-MORI set of labels; paper version of electrical plan Stop block HSK-100/SK50/CAT50 Stop block HSK-A100/SK50/CAT50 Digital Manufacturing Package Digital Manufacturing Package (1) IoTconnector Allows the use of the Online services from DMG MORI (2) Machine Data Connector (MDC) Standardized machine data interface Protocols: OPCUA, MTConnect, MQTT (3) NETservice Qualified support through internet-b Messenger V4 The latest version of DMG MORI Messenger displays web based the machine live status. It allows to analyze the machine run-time, downtime, alarms in individually configurable dashboards and transparently shows the actual status in the manufacturing shop Service Agent Service Agent Overview of all maintenance work on the machine Special equipment SK001 Preparation for Hofmann RW/NC 400 with direct measuring system ready to plug right workspace Y-0404 Micro-Aerator: For clean coolant (50HZ) État
Utilisé